This guide is available in English only for now.
Printer setup
Thermal tattoo stencil printer settings: scale, paper and density
Updated 8 अक्टूबर 20267 min read
Save to PinterestMost thermal stencil problems come down to three settings: scale, paper orientation and density. Get those right and the same file prints the same way every time.
This applies to portable thermal printers, such as the Brother PocketJet or Phomemo models, and to classic thermal copiers. Menu names differ between machines, so this guide describes what each setting does.
Quick answer
Print at 100% or actual size with fit to page switched off, then measure a known length such as the 50 mm bar on a TattooStencil PDF. Remove the protective tissue and load the paper the way the maker shows. If lines are faint, raise density one step at a time, try fresh paper and clean the print head. Use pure black on white artwork.
- Print scale
- 100%, actual size
- Calibration bar on the PDF
- 50 mm
- Layers in thermal paper
- 4
- Artwork
- Pure black on white
Step by step
Set up a thermal printer for tattoo stencils
What you need
- Thermal transfer paper
- Stencil file as PDF or PNG
- Isopropyl alcohol
- Lint free swabs
Tools
- Thermal stencil printer or thermal copier
- Phone, tablet or computer
- Ruler
- 01
Start from pure black on white artwork
Use solid black lines on a white background, with no grey. The print head only fires on dark pixels, so grey shading and soft edges print speckled or broken.
- 02
Set the scale to 100%
In the print dialog choose actual size or 100%, and switch off fit to page, scale to fit and any shrink option. Match the paper size to the sheet in the printer: A4 or Letter.
- 03
Load the paper
Remove the protective tissue. Feed the sheet straight and the right way up for your machine, following the diagram in its guide.
- 04
Print a test word
Before a full design, print a short word. It should look backwards on the underside of the white sheet, so that it reads correctly on skin.
- 05
Measure the calibration bar
Print the stencil and measure something of known length. The TattooStencil PDF has a 50 mm calibration bar. If it measures 50 mm, the scale is right.
- 06
Adjust density one step at a time
If lines are faint or broken, raise density or darkness one step and print again. If fine gaps fill in, go down a step.
- 07
Clean the head and roller
With the machine cool and unplugged, wipe the print head and roller with isopropyl alcohol on a lint free swab, and let them dry.
Scale: 100% or actual size, never fit to page
Fit to page shrinks the whole sheet to clear the printer's margins. The stencil comes out a few percent small, and on a sleeve tiled across several sheets the pieces stop lining up.
Set 100% or actual size every time, then prove it with a ruler on the 50 mm calibration bar of the TattooStencil PDF. If it reads 47 mm, for example, the print was scaled to 94%.
Loading thermal stencil paper
Thermal transfer paper has four layers: a white master sheet, a thin protective tissue, the purple carbon sheet and a yellow backing sheet. Remove the tissue before printing. Left in, it sits between the carbon and the white sheet and blocks the ink.
Which way up the sheet goes depends on the machine, so follow the diagram on the printer or in its guide. Either way, heat moves ink from the carbon onto the underside of the white sheet.
Density and darkness: fixing faint prints
Density, sometimes called darkness or heat, sets how much energy the head puts into each dot. Too little gives pale, broken lines. Too much closes small gaps. Change it one step at a time and reprint the same file to compare.
| Print problem | Likely cause | What to change |
|---|---|---|
| Faint lines over the whole sheet | Density too low, or old paper | Raise density one step. Try a fresh sheet. |
| Blank or nearly blank sheet | Paper loaded the wrong way up, or tissue left in | Remove the tissue and reload the right way up. |
| A pale streak along the sheet | Dirt on the print head | Clean the head with alcohol on a lint free swab. |
| Skewed or creased print | Sheet fed at an angle | Feed it straight and let the machine pull it. |
| Fine detail filled in | Density too high, or lines too close for the size | Lower density one step, or print larger. |
| Speckled or broken shading | Grey or soft-edged artwork | Convert the artwork to pure black on white. |
Why pure black on white prints cleaner
A thermal head has no grey: each dot fires or it does not. Grey shading and soft, anti-aliased edges have to become a pattern of dots, which prints as speckle, fuzz or broken lines.
Solid black lines on a white background make every dot a clear decision. Shading you want as a guide is better drawn as hatching than as grey.
Mirroring: test once, then leave it alone
On a thermal printer loaded as the maker instructs, the ink lands on the underside of the white sheet. That face goes against the skin, so the stencil reads correctly without mirroring the artwork.
Print a short word to confirm it on your machine: backwards on the ink side, correct on skin. Mirror the file only to flip a design on purpose. TattooStencil has a mirror toggle for that.
Maintenance that keeps prints dark
Residue builds up on the print head and roller, and prints fade or streak. Clean both with isopropyl alcohol on a lint free swab, with the machine cool and unplugged.
Store transfer paper flat in its pack, away from heat, sunlight and damp. Old or badly stored paper prints pale whatever the settings.
Common questions
Why is my stencil printer printing too light?
The usual causes are density set too low, old transfer paper, paper loaded the wrong way up, or a dirty print head. Raise density one step at a time, try a fresh sheet, check the orientation and clean the head.
What scale should I print a tattoo stencil at?
100%, also called actual size, with fit to page and scale to fit switched off. Check it by measuring a known length on the print, such as the 50 mm calibration bar on a TattooStencil PDF.
How do I load thermal stencil paper?
Remove the thin protective tissue and feed the sheet straight, the right way up for your machine. Orientation differs between printers, so follow the diagram on the machine and confirm with a test word.
Do I need to mirror the image for a thermal stencil printer?
Normally no. The ink prints onto the underside of the white sheet, which reverses it, so it reads correctly on skin. Print a short test word to confirm, and mirror only to flip a design on purpose.
Can I use a regular printer for tattoo stencils?
A regular inkjet or laser printer can print the design on plain paper for hand tracing over transfer paper. It cannot print a stencil directly, unless it is an inkjet filled with stencil ink made for that purpose.
Printer setup
Print from a file made for true size
TattooStencil sizes your design in exact centimetres on A4 or Letter, with a 50 mm calibration bar to prove the scale with a ruler. Sleeves and back pieces tile across sheets with 6 mm overlap guides. The stencil maker is free to try.
Keep reading
All guidesStencil making
How to make a tattoo stencil from a photo or drawing
Make a tattoo stencil from a photo or drawing: clean line art, the right line weight, exact size in cm, then print or hand trace onto transfer paper.
Transfer troubleshooting
Tattoo stencil not transferring: causes and fixes
Stencil too light, blurry, patchy or rubbing off? Match the symptom to its cause and fix it: skin prep, primer amount, pressure, paper and print darkness.
Stencil application
How to apply a tattoo stencil so it stays put
Apply a tattoo stencil step by step: shave and clean, a thin layer of primer, place it with the client standing, press, peel, then dry 10 to 15 minutes.